Basic update to the renesas-ra port to replace the traditional
`MICROPY_EVENT_POLL_HOOK` with the newer mp_event_wait API as appropriate.
Signed-off-by: Andrew Leech <andrew@alelec.net>
The `esp32.wake_on_ext1()` method should only be available on boards that
have SOC_PM_SUPPORT_EXT1_WAKEUP=y. And update docs to reflect this.
Signed-off-by: Meir Armon <meirarmon@gmail.com>
The `esp32.wake_on_ext0()` method should only be available on boards that
have SOC_PM_SUPPORT_EXT0_WAKEUP=y. And update docs to reflect this.
Signed-off-by: Meir Armon <meirarmon@gmail.com>
The `esp32.wake_on_touch()` method should only be available on boards that
have SOC_TOUCH_SENSOR_SUPPORTED=y. And update docs to reflect this.
Signed-off-by: Meir Armon <meirarmon@gmail.com>
In the case where an mpz number is zero, its `len` is 0 and its `dig` is
NULL. In that case, decrementing NULL via `d--` is undefined behavior
according to the C specification.
Restructuring the loops in this way avoids undefined behavior.
Also, ensure that these cases are tested in the coverage test. This
doesn't make much difference now, but would otherwise cause errors later
when the undefined behavior sanitizer is employed in CI.
Signed-off-by: Jeff Epler <jepler@gmail.com>
The `esp32.wake_on_ulp()` method should only be available on boards that
have SOC_ULP_SUPPORTED=y. Update docs to reflect this.
Signed-off-by: Meir Armon <meirarmon@gmail.com>
Remove the "vfs" entry from all partitions-*.csv files, and then remove
duplicated files.
And remove the ESP32_GENERIC_S3-FLASH_4M variant, because it's no longer
needed.
Signed-off-by: Damien George <damien@micropython.org>
Currently in the esp32 port the size of the SPI flash must be configured at
build time, eg 4MiB, 8MiB, etc. Also, the esp32 partition table must be
configured at build time, which depends on the size of the SPI flash. A
bigger flash means more can be allocated to the user filesystem.
This commit makes it so the SPI flash size is automatically determined at
runtime, and the filesystem size is automatically set to take up as much
room as possible (a "vfs" partition is created automatically if it doesn't
exist).
This works by:
- Setting the SPI flash size to be 4MiB in the build (or some other value,
as long as the firmware app fits).
- Removing the vfs partition from the esp32 partition table (only nvs,
phy_init and firmware, and maybe romfs, remain in the partition table).
- At boot, query the physical size of the SPI flash and use that as the
actual size in the code.
- If it doesn't already exist, automatically create a "vfs" partition which
takes up the flash from the end of all existing partitions to the end of
flash.
This allows simplifying a lot of board configurations, and removing some
board variants that just change the flash size (to be done in a following
commit).
It's also fully backwards compatible, in the following sense:
- Existing boards with MicroPython firmware will continue to work with the
same filesystem, ie the filesystem won't be erased when the firmware is
updated.
- If a user has a custom esp32 partition table and installs MicroPython as
a bare app into the app partition, the new MicroPython firmware will
honour the esp32 partition table and use either "vfs" or "ffat"
partitions as the filesystem.
Signed-off-by: Damien George <damien@micropython.org>
Testing shows that for frequencies which the esp8266 can handle -- up to
about 1kHz -- `machine.time_pulse_us()` now gives more accurate results.
Prior to this commit it would measure on average about 1us lower, but now
the average is much closer to the true value. For example a pulse that is
1000us long, it would measure between 998 and 1000us. Now it measures
between 999us and 1001us.
Signed-off-by: Damien George <damien@micropython.org>
This commit fixes CI test runs for the `nanbox` target, which were
broken by the unconditional native emitter code output changes in the
test runner.
The `nanbox` configuration does not enable native emitters of any kind,
and with a full test run that includes executing emitted native code
things would break when doing CI runs.
This is worked around by introducing a common subset of tests that do
not involve the native emitter, and a more comprehensive set of tests
that include both non-emitter and emitter tests. The `nanbox` CI test
run will stop at the first subset, whilst other configurations will run
that and execute further tests.
Function names have been kept the same for steps that involve native
code, with the `nanbox` subset having another one. This should not
trigger any breakage in existing CI configurations or external scripts.
Signed-off-by: Alessandro Gatti <a.gatti@frob.it>
Most extmod network drivers were being defined on a per-port basis,
duplicating code and making enabling a driver on a new port harder.
This consolidates extmod driver declarations and removes the existing
per-port definitions of them.
This commit has been verified to be a no-op in terms of firmware change.
Signed-off-by: Andrew Leech <andrew.leech@planetinnovation.com.au>
This commit updates the ADC to use the new driver `esp_adc/adc_oneshot.h`.
There are several errata notes about not being able to change the bit-width
of the ADCs certain chips. The only chip that can switch resolution to a
lower one is the normal ESP32. ESP32 C2 and S3 are stuck at 12 bits, while
S2 is at 13 bits.
On the S2, you can change the resolution, but it has no effect on the
resolution, rather, it prevents attenuation from working at all!
The resolution is set to the maximum possible for each SoC, with the ESP32
being the only one not throwing errors when trying to set the bit-width to
9, 10, 11 or 12 bits using `ADC.width(bits)`.
Signed-off-by: Damian Nowacki (purewack) bobimaster15@gmail.com
If the interrupt is not freed but merely disabled, instead of reallocating
it every time the timer is enabled again we can instead just re-enable it.
That means we're no longer setting the handler every time, and we need to
ensure it does not change. Doing so by adding an additional wrapper
function does not only solve that problem, it also allows us to remove
some code duplication and simplify how machine_uart uses the timer.
Signed-off-by: Daniël van de Giessen <daniel@dvdgiessen.nl>
esp_intr_free is not safe to call from the timer ISR because it requires
the current task (the one the ISR interrupted) to be pinned to the same
core as the interrupt was allocated on. Merely disabling the ISR however is
safe since that only requires that we're currently running on the same core
(which the ISR always is), regardless of the current task.
This was causing deadlocks in machine_uart when the ISR happened to
interrupt a task that was not pinned to a specific core.
Signed-off-by: Daniël van de Giessen <daniel@dvdgiessen.nl>
This commit adds an optional configuration option for the ESP8266 port
that, if the board rebooted due to a crash, will print to stdout some
information about the error that triggered the issue.
It is not possible using regular SDK functions to intercept errors and
print information at that stage, and the only error response from the
board is to reboot itself. This is the next best thing, print some
error information just once at boot time after the crash - the least
invasive option given the situation we're in.
This is disabled by default, and can be enabled by enabling
MICROPY_HW_HARD_FAULT_DEBUG in the port configuration - obviously with a
small increase in the firmware code footprint.
Signed-off-by: Alessandro Gatti <a.gatti@frob.it>
Test modified to reschedule itself based on a flag setting. Without the
change in the parent commit, this test executes the callback indefinitely
and hangs but with the change it runs only once each time
mp_handle_pending() is called.
Modified-by: Angus Gratton <angus@redyak.com.au>
Signed-off-by: Andrew Leech <andrew.leech@planetinnovation.com.au>
If the BLE radio stops responding before deinit is called the function can
get stuck waiting for an event that is never received, particularly if the
radio is external or on a separate core.
This commit adds a timeout, similar to the timeout already used in the init
function. Updated for nimble, btstack, esp32 and zephyr bindings.
Signed-off-by: Andrew Leech <andrew.leech@planetinnovation.com.au>
The vendor and product fields in the `board.json` files were somewhat
inconsistent. Remove any duplication of the vendor name in the product
field so that `f"{vendor} {product}"` reads well.
In addition to that, update most of the URL's for `board.json` files that
are modified here, and match case and spacing used by the manufacturers for
the vendor and product names.
Signed-off-by: Matt Trentini <matt.trentini@gmail.com>
Implements MSG_PEEK and MSG_DONTWAIT (both passed through to LWIP
sockets API).
This work was funded through GitHub Sponsors.
Signed-off-by: Angus Gratton <angus@redyak.com.au>
Add support for the boards:
- SparkFun SAMD21 Dev Breakout
- SparkFun RedBoard Turbo
Both boards are SAMD21 based and actively sold by SparkFun.
Signed-off-by: robert-hh <robert@hammelrath.com>
Adding a QSPI memory chip on a STM32G4 does not work due to some small
issues, which are fixed in this commit:
- Rename QUADSPI1_xxx alt-func names to QUADSPI_xxx, to match the static
names used in `qspi.c`.
- Enable `mpu.h` macros on G4.
- Don't include I- and D-cache invalidation on G4.
Signed-off-by: Damien George <damien@micropython.org>
This reverts commit 62e0fa04a7.
Reverting as the only linker wrap needed for nrf port was removed
in the parent commit.
This work was funded through GitHub Sponsors.
Signed-off-by: Angus Gratton <angus@redyak.com.au>
Previously MicroPython ports would linker-wrap dcd_event_handler
in order to schedule the USB task callback to run when needed.
TinyUSB 0.16 added proper support for an event hook to do the
same thing without the hacky linker wrapping.
This work was funded through GitHub Sponsors.
Signed-off-by: Angus Gratton <angus@redyak.com.au>
Changes are:
- Refactor the open-drain macros, add GPIO_ENABLE/DISABLE_OPEN_DRAIN, and
move them to `mphalport.h`.
- Only use `uint64_t` for the open-drain mask if there are more than 32
GPIOs (saves code size).
- Ensure we're shifting a `uint64_t` by using 1ULL constants.
Signed-off-by: Phil Howard <github@gadgetoid.com>
Replace custom macros with Pico SDK functions, enabling support for RP2350B
variant chips with > 32 GPIOs.
Fixes issue #17241.
Signed-off-by: Phil Howard <github@gadgetoid.com>
Prevents lightsleep being woken up every 64ms to service LWIP timers, when:
1. No netif is up, and
2. No TCP sockets are active
The TCP socket check may not be strictly necessary, but without ticking the
tcp timer they won't ever time out by themselves.
This work was funded through GitHub Sponsors.
Signed-off-by: Angus Gratton <angus@redyak.com.au>
This is a breaking change due to the signature change of `enable_irq()`.
Previously the signature was:
machine.enable_irq()
Now the signature matches other ports, and the docs, and is:
machine.enable_irq(state)
Where `state` is the return value from `machine.disable_irq()`.
Signed-off-by: Damien George <damien@micropython.org>
Some MCUs cannot write more than 255 bytes to the UART at once. Eg writing
256 bytes gets truncated to 0, writing 257 gets truncated to 1, etc.
Signed-off-by: Damien George <damien@micropython.org>
This commit adds an `attached_to_repl` property to each UART, and makes
sure that property is correctly set/unset when the UART is attached to or
detached from the REPL.
That property is then used to make sure incoming characters on the UART are
only checked for the interrupt character if the UART is attached to the
REPL. Otherwise a board without REPL on UART can have its code interrupted
if ctrl-C is received on the UART.
Also, put incoming UART characters on to `stdin_ringbuf` instead of the
UARTs ring buffer (the former is much larger than the latter).
Signed-off-by: Damien George <damien@micropython.org>
On nRF52, the physical SRAM is mapped to 0x20000000 for data access and
0x00800000 for instruction access. So, while native code is allocated and
written using addresses in the 0x20000000 range, it must execute from the
0x00800000 range.
This commit makes this work correctly on nRF52 MCUs by adjusting the
address.
Signed-off-by: Damien George <damien@micropython.org>
Support the new PHY_GENERIC device type, added in ESP-IDF v5.4.0 [1].
This PHY driver was added to ESP-IDF to support "generic"/oddball PHY
LAN chips like the JL1101, which offer no features beyond the bare
802.3 PHY standard and don't actually need a chip-specific driver (see
discussion at [2]).
[1] 0738314308
[2] https://github.com/espressif/esp-eth-drivers/pull/28
Signed-off-by: Elvis Pfutzenreuter <epxx@epxx.co>
The default I2C init does not require setting SCL or SDA but the default
I2C0 pins for C3, S3 conflict with the espressif GPIO usage.
For the C3, pins 18/19 are for USB/JTAG. If used for I2C() they will cause
the REPL to hang on initialization of the I2C.
For the S3 pin 19 is allocated for USB/JTAG also but the defaults do not
seem to affect the REPL.
See related #16956.
Fixes issue #17103.
Signed-off-by: Rick Sorensen <rick.sorensen@gmail.com>
Signed-off-by: Angus Gratton <angus@redyak.com.au>
This adds a new function, `esp32.idf_task_info()`, that can be used to
retrieve task statistics which is useful for diagnosing issues where some
tasks are using up a lot of CPU time.
It's best used in conjunction with the `utop` module from micropython-lib.
Signed-off-by: Daniël van de Giessen <daniel@dvdgiessen.nl>
This adds support for LAN8670 to the esp32 port. Enabled conditionally for
the esp32 target, if ESP-IDF version is new enough (v5.3 or newer).
Fixes issue #15731.
Signed-off-by: Damien George <damien@micropython.org>
Signed-off-by: Angus Gratton <angus@redyak.com.au>
This version of the IDF uses about 1KB more IRAM and 1KB more DRAM on most
boards, but 6.5KB more DRAM usage on the S3. It seems that's due to a lot
of small increases in many components.
Signed-off-by: Ihor Nehrutsa <Ihor.Nehrutsa@gmail.com>
Python threads (created via the `_thread` module) are backed by a FreeRTOS
task. Managing the deletion of the task can be tricky, and there are
currently some bugs with this in the esp32 port.
The actual crash seen was in FreeRTOS' `uxListRemove()`, and that's because
of two calls to `vTaskDelete()` for the same task: one in
`freertos_entry()` when the task ran to completion, and the other in
`mp_thread_deinit()`. The latter tried to delete the task a second time
because it was still in the linked list, because `vTaskPreDeletionHook()`
had not yet been called. And the reason `vTaskPreDeletionHook()` was yet
to be called is because the FreeRTOS idle task was starved.
This commit fixes that.
There are three things done by this commit:
- remove the `vTaskPreDeletionHook`, it's not needed anymore because task
stack memory is allocated by the IDF, not on the MicroPython heap
- when a task finishes it now removes itself from the linked list, just
before it deletes itself
- on soft reset, all tasks are deleted and removed from the linked list in
one swoop (while the mutex is held)
Signed-off-by: Damien George <damien@micropython.org>
This reduce inconsistencies between esp32 PWM and other ports:
1. duty_u16() high value is 2**16-1 == 65535
2. Invert PWM wave with invert=1 parameter
3. Enable PWM in light sleep mode
4. Allow PWM output and read pulse input simultaneously on the same Pin()
5. Code refactoring
Co-Authored-By: Angus Gratton <angus@redyak.com.au>
Co-Authored-By: robert-hh <robert@hammelrath.com>
Co-Authored-By: Andrew Leech <andrew.leech@planetinnovation.com.au>
Co-Authored-By: Yoann Darche <yoannd@hotmail.com>
Signed-off-by: Ihor Nehrutsa <Ihor.Nehrutsa@gmail.com>
The ESP32 PPP implementation predates the generic
implementation in extmod. The new extmod
implementation has a few advantages such as a
better deinitialisation procedure (the ESP32
implemementation would not clean up properly and
cause crashes if recreated) and using the UART IRQ
functionality instead of running a task to read
data from the UART.
This change restructures the ESP implementation to
be much closer to the new extmod version, while
also bringing a few tiny improvements from the
ESP32 version to the extmod version. The diff
between extmod/network_ppp_lwip.c and
ports/esp32/network_ppp.c is now a small set of
easy to review ESP32 port-specific changes.
Signed-off-by: Daniël van de Giessen <daniel@dvdgiessen.nl>
This commit changes the error handler for WiFi operations to recognise
out of memory conditions reported by ESP-IDF functions, and report them
as more descriptive exceptions rather than a generic "error 0x101".
The error handler only provided a human-readable error description for
WiFi-specific error codes (codes in the ESP_ERR_WIFI_BASE range), but
WiFi functions are known to return other codes. Now ESP_ERR_NO_MEM is
covered with a specific error message, making it easier to debug issues
related to running out of ESP-IDF heap.
Signed-off-by: Alessandro Gatti <a.gatti@frob.it>
If the driver was reinitialised while there was
already an event task running the queue that task
is trying to receive from would be deleted,
causing it to try to take a lock that no longer
existed and deadlocking the CPU.
This change ensures the task is always shut down
before recreating the queue and recreates the task
afterwards.
It also allows setting an IRQ handler before the
UART is initialized (like other ports allow),
removes the task when the UART is deinitialized
(which was previously missing), adds a check that
no event task can be started when no queue exists,
and adds a check to prevent reinitialising the
UART driver unnecessarily.
Signed-off-by: Daniël van de Giessen <daniel@dvdgiessen.nl>
