Changes are:
- Refactor the open-drain macros, add GPIO_ENABLE/DISABLE_OPEN_DRAIN, and
move them to `mphalport.h`.
- Only use `uint64_t` for the open-drain mask if there are more than 32
GPIOs (saves code size).
- Ensure we're shifting a `uint64_t` by using 1ULL constants.
Signed-off-by: Phil Howard <github@gadgetoid.com>
As cyw43 pins might be dynamic, add a function that returns if a pin is
reserved. This is used by `MICROPY_HW_PIN_RESERVED` to prevent the pin IRQ
from being reset across a soft-reset.
Signed-off-by: Peter Harper <peter.harper@raspberrypi.com>
Pico SDK defines `__dsb()` and `__sev()` so use those instead of the CMSIS
equivalents. This matches the use of `__wfi()` in lieu of `__WFI()` and
lowers the dependency on CMSIS headers.
And then, move the include of "RP2040.h" from the widely-included
"mphalport.h" to specific source files that need this header, to keep its
inclusion contained.
Signed-off-by: Phil Howard <phil@gadgetoid.com>
The best_effort_wfe_or_timeout() and sleep_us() pico-sdk functions use the
pico-sdk alarm pool internally, and that has a bug.
Some usages inside pico-sdk (notably multicore_lockout_start_blocking())
will still end up calling best_effort_wfe_or_timeout(), although usually
with "end_of_time" as the timeout value so it should avoid any alarm pool
race conditions.
This work was funded through GitHub Sponsors.
Signed-off-by: Angus Gratton <angus@redyak.com.au>
Following ad806df857 where the
MICROPY_PY_PENDSV_ENTER/REENTER/EXIT macro definitions were moved to
mphalport.h.
Signed-off-by: Damien George <damien@micropython.org>
Also move MICROPY_PY_PENDSV_ENTER/REENTER/EXIT to mphalport.h, for ports
where these are not already there.
This helps separate the hardware implementation of these macros from the
MicroPython configuration (eg for renesas-ra and stm32, the IRQ static
inline helper functions can now be moved to irq.h).
Signed-off-by: Damien George <damien@micropython.org>
Currently on rp2 the time.time_ns() function has only seconds resolution.
This commit makes it have microsecond resolution, by using the output of
time_us_64() instead of the RTC.
Tested that it does not drift from the RTC over long periods of time.
Signed-off-by: Damien George <damien.p.george@gmail.com>
Prior to this commit, Pin(Pin.OPEN_DRAIN, value=0) would not set the
initial value of the open-drain pin to low, instead it would be high.
Signed-off-by: Damien George <damien@micropython.org>
When switching from a special function like SPI to an input or output,
there was a brief period after the function was disabled but before the
pin's I/O state was configured, in which the state would be poorly defined.
This fixes the problem by switching off the special function after fully
configuring the I/O state.
Fixes#10226.
Signed-off-by: Paul Grayson <pdg@alum.mit.edu>
If USB CDC is connected and the board sends data, but the host does not
receive the data, the device locks up. This is fixed in this commit by
having a timeout of 500ms, after which time the transmission is skipped.
Fixes issue #9634.
This includes:
- Configuration file for the cyw43-driver.
- Integration of cyw43-driver into the build, using lwIP.
- Enhancements to machine.Pin to support extension IO pins provided by the
CYW43xx.
- More mp-hal pin helper functions.
- mp_hal_get_mac_ascii MAC address helper function.
- Addition of rp2.country() function to set the country code.
A board can enable this driver by setting MICROPY_PY_NETWORK_CYW43 in their
cmake snippet.
Work done in collaboration with Graham Sanderson and Peter Harper.
Signed-off-by: Damien George <damien@micropython.org>
This commit adds a new port "rp2" which targets the new Raspberry Pi RP2040
microcontroller.
The build system uses pure cmake (with a small Makefile wrapper for
convenience). The USB driver is TinyUSB, and there is a machine module
with most of the standard classes implemented. Some examples are provided
in the examples/rp2/ directory.
Work done in collaboration with Graham Sanderson.
Signed-off-by: Damien George <damien@micropython.org>
