Most extmod network drivers were being defined on a per-port basis,
duplicating code and making enabling a driver on a new port harder.
This consolidates extmod driver declarations and removes the existing
per-port definitions of them.
This commit has been verified to be a no-op in terms of firmware change.
Signed-off-by: Andrew Leech <andrew.leech@planetinnovation.com.au>
Stop using soft timer for `mp_wfe_or_timeout`. Now uses the alarm pool
again as issues with this code have been fixed. This resolves the "sev"
issue that stops the RP2350 going idle.
Also, change the lightsleep code to use the hardware timer library and
alarm 1, as alarm 2 is used by and soft timers and alarm 3 is used by the
alarm pool.
Signed-off-by: Peter Harper <peter.harper@raspberrypi.com>
PSRAM will be used exclusively if MICROPY_GC_SPLIT_HEAP == 0, it will be
added to RAM if MICROPY_GC_SPLIT_HEAP == 1, and the system will fall back
to RAM only if it's not detected.
Due to the size of PSRAM, GC stack was overflowing and causing the GC to
scan through the entire memory pool. This caused noticable slowdowns
during GC. Increase the stack from 256 to 4096 bytes to avoid overflow and
increase the stack entry type size to accomodate 8MB+ PSRAM.
Changes are:
- ports/rp2/mpconfigport.h: Make split-heap optional and enable by default.
- ports/rp2/mpconfigport.h: Increase GC stack entry type to uint32_t.
- ports/rp2/mpconfigport.h: Raise GC stack size.
Co-authored-by: Kirk Benell <kirk.benell@sparkfun.com>
Signed-off-by: Phil Howard <github@gadgetoid.com>
Performs a best-effort attempt to detect attached PSRAM, configure it and
*add* it to the MicroPython heap. If PSRAM is not present, should fall
back to use internal RAM.
Introduce two new port/board defines:
- MICROPY_HW_ENABLE_PSRAM to enable PSRAM.
- MICROPY_HW_PSRAM_CS_PIN to define the chip-select pin (required).
Changes are:
- ports/rp2/rp2_psram.[ch]: Add new PSRAM module.
- ports/rp2/main.c: Add optional PSRAM support.
- ports/rp2/CMakeLists.txt: Include rp2_psram.c.
- ports/rp2/mpconfigport.h: Add MICROPY_HW_ENABLE_PSRAM.
- ports/rp2/modmachine.c: Reconfigure PSRAM on freq change.
Co-authored-by: Kirk Benell <kirk.benell@sparkfun.com>
Co-authored-by: Mike Bell <mike@mercuna.com>
Signed-off-by: Phil Howard <phil@gadgetoid.com>
Not enabled by default on any board. A board can enable a ROMFS partition
by defining `MICROPY_HW_ROMFS_BYTES` in its `mpconfigboard.h` file. For
example:
#define MICROPY_HW_ROMFS_BYTES (128 * 1024)
The ROMFS partition is placed at the end of the flash allocated for the
firmware, giving less space for the firmware. It then lives between the
firmware and the read/write filesystem.
Signed-off-by: Damien George <damien@micropython.org>
Also add the default values of these macros to the respective
`mpconfigport.h` files, to improve discoverability.
Signed-off-by: Angus Gratton <angus@redyak.com.au>
This commit enables by default inline assembly support for the RP2 target
when it is operating in RISC-V mode. This brings the feature set when in
RISC-V mode to parity with what's available in ARM mode.
Signed-off-by: Alessandro Gatti <a.gatti@frob.it>
LFN type 2 uses the stack to allocate the internal working buffer for LFN,
which is thread-safe and saves about 512 bytes of BSS memory (at the
expense of needing that much memory on the stack).
Signed-off-by: iabdalkader <i.abdalkader@gmail.com>
The port configuration file tagged callable pointers' LSB on both Arm
and RISC-V variants. This is needed on Arm due to Thumb/Thumb2
code addresses having their LSB set, but on RISC-V this is not required.
Signed-off-by: Alessandro Gatti <a.gatti@frob.it>
Supported trigger names: IRQ_RXIDLE, IRQ_TXIDLE, IRQ_BREAK
- IRQ_RXIDLE: The handler for IRQ_RXIDLE is called reliably 31 UART bit
times after the last incoming data.
- IRQ_TXIDLE: This IRQ is triggered after at least >5 characters are sent
at once. It is triggered when the TX FIFO falls below 4 elements. At
that time, up to 5 bytes may still be in the FIFO and output shift
register.
- IRQ_BREAK: The IRQ triggers if a BREAK state is detected at RX.
Properties & side effects:
- After a BREAK, a valid character must be received before another break
can be detected.
- Each break puts a 0xff character into the input buffer.
The irq.flags() value is cleared only with a new wanted event. Do not
change the flags otherwise.
Signed-off-by: robert-hh <robert@hammelrath.com>
By default, the peripheral clock for UART and SPI is set to 48 MHz and will
not be affected by the MCU clock change. This can be changed by a second
argument to `machine.freq(freq, peripheral_freq)`. The second argument
must be either 48 MHz or identical with the first argument.
Note that UART and SPI baud rates may have to be re-configured after
changing the MCU clock.
Signed-off-by: robert-hh <robert@hammelrath.com>
Progress towards removing pico-sdk alarm pool, due to a known issue.
This work was funded through GitHub Sponsors.
Signed-off-by: Angus Gratton <angus@redyak.com.au>
Disabled by default, but enabled on all boards that previously had
`MICROPY_PY_MACHINE_BARE_METAL_FUNCS` enabled.
Signed-off-by: Damien George <damien@micropython.org>
Following ad806df857 where the
MICROPY_PY_PENDSV_ENTER/REENTER/EXIT macro definitions were moved to
mphalport.h.
Signed-off-by: Damien George <damien@micropython.org>
This commit changes all uses in the rp2 port, and drivers that are
optionally supported by that port.
The old MICROPY_EVENT_POLL_HOOK and MICROPY_EVENT_POLL_HOOK_FAST macros are
no longer used for rp2 builds and are removed (C user code will need to be
changed to suit).
Also take the opportunity to change some timeouts that used 64-bit
arithmetic to 32-bit, to hopefully claw back a little code size.
This work was funded through GitHub Sponsors.
Signed-off-by: Angus Gratton <angus@redyak.com.au>
Also move MICROPY_PY_PENDSV_ENTER/REENTER/EXIT to mphalport.h, for ports
where these are not already there.
This helps separate the hardware implementation of these macros from the
MicroPython configuration (eg for renesas-ra and stm32, the IRQ static
inline helper functions can now be moved to irq.h).
Signed-off-by: Damien George <damien@micropython.org>
The ports esp32, mimxrt, rp2 and samd all shared exactly the same
implementation of machine.disable_irq() and machine.enable_irq(),
implemented in terms of MICROPY_{BEGIN,END}_ATOMIC_SECTION. This commit
factors these implementations into extmod/modmachine.c.
The cc3200, esp8266, nrf, renesas-ra and stm32 ports do not yet use this
common implementation.
Signed-off-by: Damien George <damien@micropython.org>
Minor changes for consistency are:
- nrf gains: unique_id(), freq() [they do nothing]
- samd: deepsleep() now resets after calling lightsleep()
- esp32: lightsleep()/deepsleep() no longer take kw arg "sleep", instead
it's positional to match others. also, passing 0 here will now do a 0ms
sleep instead of acting like nothing was passed.
reset_cause() no longer takes any args (before it would just ignore them)
- mimxrt: freq() with an argument and lightsleep() both raise
NotImplementedError
Signed-off-by: Damien George <damien@micropython.org>
This is a code factoring to have the dict for the machine module in one
location, and all the ports use that same dict. The machine.soft_reset()
function implementation is also factored because it's the same for all
ports that did already implement it. Eventually more functions/bindings
can be factored.
All ports remain functionally the same, except:
- cc3200 port: gains soft_reset, mem8, mem16, mem32, Signal; loses POWER_ON
(which was a legacy constant, replaced long ago by PWRON_RESET)
- nrf port: gains Signal
- qemu-arm port: gains soft_reset
- unix port: gains soft_reset
- zephyr port: gains soft_reset, mem8, mem16, mem32
Signed-off-by: Damien George <damien@micropython.org>
This change:
- Has a small code size reduction.
- Should slightly improve overall performance. The old hook code
seemed to use between 0.1% and 1.6% of the total CPU time doing no-op
calls even when no USB work was required.
- USB performance is mostly the same, there is a small increase in
latency for some workloads that seems to because sometimes the hook
usbd_task() is called at the right time to line up with the next USB host
request. This only happened semi-randomly due to the timing of the hook.
Improving the wakeup latency by switching rp2 to tickless WFE allows the
usbd_task() to run in time for the next USB host request almost always,
improving performance and more than offsetting this impact.
This work was funded through GitHub Sponsors.
Signed-off-by: Angus Gratton <angus@redyak.com.au>
The main motivation for doing this was to reduce the latency when the
system is woken by a USB interrupt. The best_effort_wfe_or_timeout()
function calls into the pico-sdk dynamic timer framework which sets up a
new dynamic timer instance each time, and then has to tear it down before
continuing after a WFE.
Testing Python interrupt latency, it seems to be improved by about 12us
(from average of 46us to 34us running a Pin IRQ). C-based "scheduled
nodes" should see even lower latency.
This work was funded through GitHub Sponsors.
Signed-off-by: Angus Gratton <angus@redyak.com.au>
This is a code factoring to have the Python bindings in one location, and
all the ports use those same bindings. For all ports except the two listed
below there is no functional change.
The nrf port has UART.sendbreak() removed, but this method previously did
nothing.
The zephyr port has the following methods added:
- UART.init(): supports setting timeout and timeout_char.
- UART.deinit(): does nothing, just returns None.
- UART.flush(): raises OSError(EINVAL) because it's not implemented.
- UART.any() and UART.txdone(): raise NotImplementedError.
Signed-off-by: Damien George <damien@micropython.org>
No functional change, just code factoring to have the Python bindings in
one location, and all the ports use those same bindings.
Signed-off-by: Damien George <damien@micropython.org>
This factors the basic top-level I2S class code from the ports into
extmod/machine_i2s.c:
- I2S class definition and method table.
- The init and deinit method wrappers.
- The make_new code.
Further factoring will follow.
Signed-off-by: Damien George <damien@micropython.org>
There are currently 7 ports that implement machine.WDT and a lot of code is
duplicated across these implementations. This commit factors the common
parts of all these implementations to a single location in
extmod/machine_wdt.c. This common code provides the top-level Python
bindings (class and method wrappers), and then each port implements the
back end specific to that port.
With this refactor the ports remain functionally the same except for:
- The esp8266 WDT constructor now takes keyword arguments, and accepts the
"timeout" argument but raises an exception if it's not the default value
(this port doesn't support changing the timeout).
- The mimxrt and samd ports now interpret the argument to WDT.timeout_ms()
as signed and if it's negative truncate it to the minimum timeout (rather
than it being unsigned and a negative value truncating to the maximum
timeout).
Signed-off-by: Damien George <damien@micropython.org>
Updates any includes, and references from Makefiles/CMake.
This essentially reverts what was done long ago in commit
136b5cbd76
This work was funded through GitHub Sponsors.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
These have by default FAT support. The SAMD21 build does not support FAT.
The nrf port also implements os.sync(), but has it's own copy of moduos.c.
Code size increases seen: 40 to 56 bytes.
Signed-off-by: robert-hh <robert@hammelrath.com>
All ports that enable MICROPY_PY_MACHINE_PWM now enable these two
sub-options, so remove these sub-options altogether to force consistency in
new ports that implement machine.PWM.
Signed-off-by: Damien George <damien@micropython.org>
This adds support for freq/duty_u16/duty_ns keyword arguments in the PWM
constructor, and adds the PWM.init() method. Using init() without
arguments enables a previously deinit-ed PWM again.
Further changes in this commit:
- Do not start PWM output if only duty was set.
- Stop all PWM slices on soft-reset.
- Fix a bug when changing the freq on a channel pair with duty_ns set.
This adds a mechanism to track a pending notify/indicate operation that
is deferred due to the send buffer being full. This uses a tracked alloc
that is passed as the content arg to the callback.
This replaces the previous mechanism that did this via the global pending
op queue, shared with client read/write ops.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
Previously, setting MICROPY_HW_ENABLE_USBDEV to 0 caused build errors. The
change affects the nrf and samd ports as well, so MICROPY_HW_ENABLE_USBDEV
had to be explicitly enabled there.
The configuration options MICROPY_HW_ENABLE_USBDEV and
MICROPY_HW_ENABLE_UART_REPL are independent, and can be enabled or disabled
by a board.
Signed-off-by: Damien George <damien@micropython.org>
This function seems to work fine in multi-core applications now.
The delay is now in units of microseconds instead of depending on the clock
speed, and is adjustable by board configuration headers.
Also added documentation.
This removes the previous WiFi driver from drivers/cyw43 (but leaves behind
the BT driver), and makes the stm32 port (i.e. PYBD and Portenta) use the
new "lib/cyw43-driver" open-source driver already in use by the rp2 port.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This provides a standard interface to setting the global networking config
for all interfaces and interface types.
For ports that already use either a static hostname (mimxrt, rp2) they will
now use the configured value. The default is configured by the port
(or optionally the board).
For interfaces that previously supported .config(hostname), this is still
supported but now implemented using the global network.hostname.
Similarly, pyb.country and rp2.country are now deprecated, but the methods
still exist (and forward to network.hostname).
Because ESP32/ESP8266 do not use extmod/modnetwork.c they are not affected
by this commit.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
