This commit adds preliminary support for ST's new STM32N6xx MCUs.
Supported features of this MCU so far are:
- basic clock tree initialisation, running at 800MHz
- fully working USB
- XSPI in memory-mapped mode
- machine.Pin
- machine.UART
- RTC and deepsleep support
- SD card
- filesystem
- ROMFS
- WiFi and BLE via cyw43-driver (SDIO backend)
Note that the N6 does not have internal flash, and has some tricky boot
sequence, so using a custom bootloader (mboot) is almost a necessity.
Signed-off-by: Damien George <damien@micropython.org>
This commit renames the NORETURN macro, indicating to the compiler
that a function does not return, into MP_NORETURN to maintain the same
naming convention of other similar macros.
To maintain compaitiblity with existing code NORETURN is aliased to
MP_NORETURN, but it is also deprecated for MicroPython v2.
This changeset was created using a similar process to
decf8e6a8b ("all: Remove the "STATIC"
macro and just use "static" instead."), with no documentation or python
scripts to change to reflect the new macro name.
Signed-off-by: Alessandro Gatti <a.gatti@frob.it>
MicroPython code may rely on the return value of sys.stdout.buffer.write()
to reflect the number of bytes actually written. While in most scenarios a
write() operation is successful, there are cases where it fails, leading to
data loss. This problem arises because, currently, write() merely returns
the number of bytes it was supposed to write, without indication of
failure.
One scenario where write() might fail, is where USB is used and the
receiving end doesn't read quickly enough to empty the receive buffer. In
that case, write() on the MicroPython side can timeout, resulting in the
loss of data without any indication, a behavior observed notably in
communication between a Pi Pico as a client and a Linux host using the ACM
driver.
A complex issue arises with mp_hal_stdout_tx_strn() when it involves
multiple outputs, such as USB, dupterm and hardware UART. The challenge is
in handling cases where writing to one output is successful, but another
fails, either fully or partially. This patch implements the following
solution:
mp_hal_stdout_tx_strn() attempts to write len bytes to all of the possible
destinations for that data, and returns the minimum successful write
length.
The implementation of this is complicated by several factors:
- multiple outputs may be enabled or disabled at compiled time
- multiple outputs may be enabled or disabled at runtime
- mp_os_dupterm_tx_strn() is one such output, optionally containing
multiple additional outputs
- each of these outputs may or may not be able to report success
- each of these outputs may or may not be able to report partial writes
As a result, there's no single strategy that fits all ports, necessitating
unique logic for each instance of mp_hal_stdout_tx_strn().
Note that addressing sys.stdout.write() is more complex due to its data
modification process ("cooked" output), and it remains unchanged in this
patch. Developers who are concerned about accurate return values from
write operations should use sys.stdout.buffer.write().
This patch might disrupt some existing code, but it's also expected to
resolve issues, considering that the peculiar return value behavior of
sys.stdout.buffer.write() is not well-documented and likely not widely
known. Therefore, it's improbable that much existing code relies on the
previous behavior.
Signed-off-by: Maarten van der Schrieck <maarten@thingsconnected.nl>
This is a code factoring to have the Python bindings in one location, and
all the ports use those same bindings. For all ports except the two listed
below there is no functional change.
The nrf port has UART.sendbreak() removed, but this method previously did
nothing.
The zephyr port has the following methods added:
- UART.init(): supports setting timeout and timeout_char.
- UART.deinit(): does nothing, just returns None.
- UART.flush(): raises OSError(EINVAL) because it's not implemented.
- UART.any() and UART.txdone(): raise NotImplementedError.
Signed-off-by: Damien George <damien@micropython.org>
This commit adds initial support for STM32H5xx MCUs. The following
features have been confirmed to be working on an STM32H573:
- UART over REPL and USB CDC
- USB CDC and MSC
- internal flash filesystem
- machine.Pin
- machine.SPI transfers with DMA
- machine.ADC
- machine.RTC
- pyb.LED
- pyb.Switch
- pyb.rng
- mboot
Signed-off-by: Damien George <damien@micropython.org>
To avoid any I/O glitches in mp_hal_pin_config, make sure a valid alternate
function is set in AFR first before switching the pin mode. When switching
from AF to INPUT or OUTPUT, the AF in AFR will remain valid up until the
pin mode is switched.
This commit adds support for the STM32G4 series of MCUs, and a board
definition for NUCLEO_G474RE. This board has the REPL on LPUART1 which is
connected to the on-board ST-link USB-UART.
This new series of MCUs is similar to the L4 series with an additional
Cortex-M0 coprocessor. The firmware for the wireless stack must be managed
separately and MicroPython does not currently interface to it. Supported
features so far include: RTC, UART, USB, internal flash filesystem.
Use uos.dupterm for REPL configuration of the main USB_VCP(0) stream on
dupterm slot 1, if USB is enabled. This means dupterm can also be used to
disable the boot REPL port if desired, via uos.dupterm(None, 1).
For efficiency this adds a simple hook to the global uos.dupterm code to
work with streams that are known to be native streams.
This patch allows to completely compile-out support for USB, and no-USB is
now the default. If a board wants to enable USB it should define:
#define MICROPY_HW_ENABLE_USB (1)
And then one or more of the following to select the USB PHY:
#define MICROPY_HW_USB_FS (1)
#define MICROPY_HW_USB_HS (1)
#define MICROPY_HW_USB_HS_IN_FS (1)
Newer versions of the HAL use names which are cleaner and more
self-consistent amongst the HAL itself. This patch switches to use those
names in most places so it is easier to update the HAL in the future.
The legacy function pyb.repl_uart() is still provided and retains its
original behaviour (it only accepts a UART object). uos.dupterm() will now
accept any object with write/readinto methods. At the moment there is just
1 dupterm slot.
Header files that are considered internal to the py core and should not
normally be included directly are:
py/nlr.h - internal nlr configuration and declarations
py/bc0.h - contains bytecode macro definitions
py/runtime0.h - contains basic runtime enums
Instead, the top-level header files to include are one of:
py/obj.h - includes runtime0.h and defines everything to use the
mp_obj_t type
py/runtime.h - includes mpstate.h and hence nlr.h, obj.h, runtime0.h,
and defines everything to use the general runtime support functions
Additional, specific headers (eg py/objlist.h) can be included if needed.
This is to keep the top-level directory clean, to make it clear what is
core and what is a port, and to allow the repository to grow with new ports
in a sustainable way.
